The main goal of the plan layout design is: "According to the arrangement of workshops from the beginning to the end of the operation, logically." For most workshops, the layout is a set of process flow, and the relative position of each device is the focus of our attention. Since the space allocated to a certain equipment in each factory is different, we do not want to describe the placement of specific equipment here, but rather make some suggestions on the equipment placement ideas. Such as the correlation between each link in the process, how to improve work efficiency.
Printing area
1. When considering the position of the printing press, it should be considered that the printing material can be easily transferred.
2. Use adhesive tape to mark the area on the ground where the equipment is to be installed (actual size).
3, to allow enough open space between devices for ventilation, especially those relatively short equipment.
4. Determine the storage location of the printing material before it is moved into the printing area.
5. Determine the best position for the printing material to be placed in the printing process, leaving an appropriate space for the placement of different prints.
6, to determine the print place after drying.
7. Check the exhaust capacity of the exhaust dryer.
8, to ensure that the circuit, piping, drainage, gas, etc. are all on you.
9. Ensure that the quality inspection area is within the production line or adjacent to the quality inspection area.
10. Leave a safe passage between the device and the wall.
11. Leave a proper distance for maintenance operations.
12. Ensure that employees can anticipate the situation after equipment expansion or reset.
13. The safety of employees is the top priority, and equipment must not be allowed to block emergency passages.
Disposal of raw materials It takes time to transfer raw materials from one location to another. Minimizing the time spent is an important function of the factory layout. The use of appropriate equipment to transport paper and other materials is critical to maintaining the high efficiency of the entire plant.
Eric C. Schmidt in his article "Materials Disposal Solutions" (Graphic Art Monthly magazine) describes the points to be considered when choosing a forklift for a printing company:
1, the type of raw materials handling
2, the weight of the goods
3, transport distance
4, the width of the aisle
5, the height to be promoted
6, reversing the necessary distance
7, ground conditions
8, the physical space occupied by the equipment
9, the cleanliness of the ceiling
10. Handling conditions - docking, slopes, etc.
11, whether the raw materials are stacked, whether in the stacker or stacker
12. Is the device capable of other work?
13, can not give up good equipment because of price issues
Printing area
1. When considering the position of the printing press, it should be considered that the printing material can be easily transferred.
2. Use adhesive tape to mark the area on the ground where the equipment is to be installed (actual size).
3, to allow enough open space between devices for ventilation, especially those relatively short equipment.
4. Determine the storage location of the printing material before it is moved into the printing area.
5. Determine the best position for the printing material to be placed in the printing process, leaving an appropriate space for the placement of different prints.
6, to determine the print place after drying.
7. Check the exhaust capacity of the exhaust dryer.
8, to ensure that the circuit, piping, drainage, gas, etc. are all on you.
9. Ensure that the quality inspection area is within the production line or adjacent to the quality inspection area.
10. Leave a safe passage between the device and the wall.
11. Leave a proper distance for maintenance operations.
12. Ensure that employees can anticipate the situation after equipment expansion or reset.
13. The safety of employees is the top priority, and equipment must not be allowed to block emergency passages.
Disposal of raw materials It takes time to transfer raw materials from one location to another. Minimizing the time spent is an important function of the factory layout. The use of appropriate equipment to transport paper and other materials is critical to maintaining the high efficiency of the entire plant.
Eric C. Schmidt in his article "Materials Disposal Solutions" (Graphic Art Monthly magazine) describes the points to be considered when choosing a forklift for a printing company:
1, the type of raw materials handling
2, the weight of the goods
3, transport distance
4, the width of the aisle
5, the height to be promoted
6, reversing the necessary distance
7, ground conditions
8, the physical space occupied by the equipment
9, the cleanliness of the ceiling
10. Handling conditions - docking, slopes, etc.
11, whether the raw materials are stacked, whether in the stacker or stacker
12. Is the device capable of other work?
13, can not give up good equipment because of price issues
Bone China Bowl,Ceramic Bowls,Porcelain Tureen
Jiabaien Ceramics Co., Ltd. , http://www.czjbeceramics.com